Numerical Analysis of Blade Stress of Marine Propellers

Kai Yu&Peikai Yan&Jian Hu

Abstract In this study,a series of numerical calculations are carried out in ANSYS Workbench based on the unidirectional fluid–solid coupling theory.Using the DTMB 4119 propeller as the research object,a numerical simulation is set up to analyze the open water performance of the propeller,and the equivalent stress distribution of the propeller acting in the flow field and the axial strain of the blade are analyzed.The results show that FLUENT calculations can provide accurate and reliable calculations of the hydrodynamic load for the propeller structure.The maximum equivalent stress was observed in the blade near the hub,and the tip position of the blade had the largest stress.With the increase in speed,the stress and deformation showed a decreasing trend.

Keywords Marine propeller .Stress distribution .Deformation distribution .Open water performance .Fluid .solid coupling

1 Introduction

With the development of large-scale civil ships, the unevenness of the wake flow field at the surface of the ship’s propeller has increased, causing deterioration in the working environment of the propeller.An increase in the power of the host increases the load per unit area of the propeller.These effects require a high strength of the propeller. To improve the propeller strength, the minimum thickness of the propeller blade and the stress distribution of the blade must be considered(Zhao 2003).Many scholars have conducted research on the hydrodynamic performance of propellers and developed many research methods,such as the lifting-line method (Lerbs 1952), lifting-surface method(Sparenberg 1960; Tsakonas et al. 1966; Cummings 1973; Kerwin and Lee 1978; Greeley and Kerwin 1982;Lee 1980), and panel method (Kerwin 1987; Lee 1987;Yamasaki and Ikehata 1992; Koyama 1994; Hoshino 1990). Several scholars have also examined the strength of propellers using fluid–structure interaction (FSI)methods. Lin and Lin (1996) used the lift-surface method and nine-node degenerated shell finite element coupling algorithm to understand the hydrodynamic performance of propellers made of composite materials. Young (2007)studied the panel method and method coupled ABAQUS with the propeller hydroelastic calculation. Zhang et al.(2014) examined the influence of the deformation of propeller blades on the surface pressure, surrounding flow field, and open water performance by using the FSI method. Yang et al. (2015) used computational fluid dynamics (CFD)based on the viscous flow theory combined with the finite element software to calculate the bidirectional FSI of glass fiber composite propellers and nickel–aluminum bronze propellers without considering the laminate structure.He et al.(2014)conducted a numerical simulation of the FSI of a propeller based on the Visual Basic for Applications (VBA) technology in a general-use software,MS Excel,combined with a self-developed propeller hydrodynamic analysis code and a secondary development of a structural commercial software. Zou et al. (2017)discussed the influence of a hub on the performance of a propeller under FSI. Huang et al. (2015) compared the accuracy of calculations of a propeller made of the samemetal material using the FSI method and the traditional CFD method. Ren et al. (2015) used the unidirectional FSI and bidirectional FSI methods to calculate and compare the static stress and total deformation of a propeller. Wang et al. (2014) used the unidirectional FSI method to calculate and analyze the structural strength of the propeller and verified the rationality of the method by comparing it with the safety factor recommended in the literature. Huang et al. (2017a, 2017b, 2017c) conducted many studies on composite propellers, compared them with copper propellers, and found that composite propellers are more susceptible to hydrodynamic loads.Li et al. (2018) analyzed the added mass and damping matrices due to FSI and examined the effects of the propeller’s skew angle and incoming flow velocity on the two matrices.Li et al.(2019)calculated the hydrodynamic performance and structural response of a composite DTMB 4381 propeller in a heterogeneous flow field in ANSYS Composite PrepPost (ACP).

Table 1 Geometric features of the propeller

Figure 1 Computational domain of the propeller flow field

In this study,we verify the reliability of the hydrodynamic load calculation by using CFD and use the ANSYS FLUENT unidirectional FSI method to calculate,analyze,and compare the equivalent stress and total deformation of a propeller at different advance speeds and study the propeller deformation characteristics of different materials.

When marine propellers are working, they are subject to multiple forces, such as gravity, centrifugal force, and hydrodynamic load.The stress is complex,which leads to cavitation erosion,fatigue fracture,and other problems.Previous studies have validated the feasibility of FSI in the analysis of propeller strength.In this study,the numerical simulation is extended to off-design conditions.Moreover,a composite propeller has become increasingly popular in engineering applications.Both of these problems deserve more detailed investigations. Here, a numerical calculation of propeller hydrodynamics is performed and compared with experimental data in the literature. Then,the hydrodynamic force is applied to the propeller through the finite element method, and the size and distribution of the equivalent force and axial strain of propellers made of different materials in open water are determined, which can provide a theoretical basis for the design optimization of propellers.

2 Theoretical Basis

2.1 Hydrodynamic Analysis

The propeller rotating in a viscous fluid at a certain speed is simulated.

The continuity equation can be expressed as

where ρ is the liquid density and uiis the velocity.

Table 2 Calculation results of open water performance

Figure 2 Comparison of the calculated and experimental results

where u,v,and w are the velocity components.

The results show that the inlet velocity is given and the normal gradient of pressure is zero.

Figure 3 Pressure distribution of the blade surface

Figure 4 FEA model of the propeller

2.2 Structural Analysis

In this paper,the uniaxial FSI method is used to calculate the force applied on the propeller at a steady state. The finite element equation of the static analysis is as follows:

where K is the stiffness matrix of the propeller; u is the displacement vector matrix of the propeller node; and F is the load applied on the propeller,consisting of centrifugal force,gravity,and fluid pressure.

3 Numerical Simulation of the Flow Field

In the third part,the numerical calculation of the propeller hydrodynamics is performed and compared with the experimental data in the literature. Then, the hydrodynamic force is applied to the propeller by using the finite element method to complete the strength calculation and analysis.

Table 3 Propeller material characteristics

3.1 Propeller Parameters

The DTMB P4119 propeller used in this study is a threebladed propeller without side slant and back tilt. Its dimensions are listed in Table 1(Yin and Kinnas 2001).

3.2 CFD Calculation Model

The entire computational domain is divided into two parts:rotational domain and static domain.The diameter of the static field is 4D,the entrance boundary diameter is 2.5D from the propeller, and the exit boundary diameter is approximately 3.5D from the propeller.The rotating cylindrical domain has a diameter of 1.2D and a length of 0.7D. The rotating and stationary domains use a high-quality hexahedral structured mesh and transfer the data by defining an interface with a total of 2.5 million meshes. The turbulence model uses the SST model. The propeller flow field computational domain is shown in Figure 1.

3.3 Boundary Condition Setting

The static domain is stationary relative to the absolute coordinate system,and the rotation domain is rotating at a constant velocity around the x-axis with a magnitude of –600 r/min with respect to a set dynamic reference system. The inlet is set as the speed inlet, given the inflow velocity at the corresponding speed coefficient; the outlet is set as the outflow boundary;and the blade and hub wall are set to no-slip solid wall.

The calculation relationship between the forward speed and the forward speed coefficient is

where n is the propeller rotational speed,D is the diameter of the propeller,and VAis the flow speed at the inlet.

3.4 Calculation Results

3.4.1 Calculation of Open Water Performance

The solution formula for the hydrodynamic coefficient is as follows:

where KTis the thrust coefficient,T is the thrust force,KQis the torque coefficient,Q is the torque,η is the efficiency,and J is the forward speed coefficient.

Table 4 Maximum stress and strain of propellers made of different materials

Figure 5 Maximum stress curve of the propellers made of different materials

Figure 6 Maximum deformation curve of the propellers made of different materials

Figure 7 Deformation distribution of the propeller

The forward speed coefficient has values of 0.4, 0.5, 0.6,0.7,0.8,0.833,0.9,1.0,and 1.1.The comparison results of the test value under the specific speed coefficient are shown in Table 2(Miao and Sun 2011).

Based on these results, a graph is drawn, as shown in Figure 2.

It can be seen from Figure 2 that the numerical calculation results are similar to the literature test results,indicating that a reliable hydrodynamic load can be obtained from the numerical calculation.

3.4.2 Pressure Distribution on the Surface of the Blade

Taking the forward speed coefficients of 0.5, 0.833, and 1.1 as an example,the pressure distribution of the pressure surface and the suction surface of the blade is given, as shown in Figure 3.

Figure 8 Stress distribution of the propeller

Figure 3 shows that the maximum pressure occurs at the leading edge of the propeller.

4 Finite Element Calculation of the Blade Stress

4.1 Propeller Meshing and Condition Setting

The propeller stress was calculated using the ANSYS WORKBENCH software.The finite element model is shown in Figure 4,and the number of meshes is 66 446.The propeller rotates around the x-axis at a fixed velocity of –600 r/min,applying a fixed-end boundary condition to both ends of the hub, and the hydrodynamic load is calculated by using FLUENT onto the finite element model of the propeller.The blade materials were selected from six different isotropic materials,as shown in Table 3.

4.2 Calculation Results

4.2.1 Stresses of Propellers Made of Different Materials

Table 4 shows the maximum equivalent stress and maximum deformation value of the blades for the six different isotropic materials at different speed factors.According to the values in Table 4,the curve of the maximum stress and maximum deformation with the advance speed coefficient is shown in Figures 5 and 6.

The analyses of Table 4,Figure 5,and Figure 6 show that with an increase in the forward speed coefficient, the maximum equivalent stress and the maximum deformation of propellers made of different materials decrease; the maximum deformation of the metallic propeller given in this study is higher by one magnitude compared with the maximum deformation of the non-metallic propeller; the deformation of the metallic propeller is very small and will have little influence on the flow field,indicating that it is reasonable to calculate the strength of the metallic propeller using the unidirectional FSI method.

4.2.2 Stress Distribution of the Propeller

Taking the nickel–aluminum bronze propeller as an example,the forward speed coefficients have values of 0.5,0.833,and 1.1, and the equivalent stress and strain distribution of the propeller are analyzed, as shown in Figures 6, 7, and 8. The strain at the tip of the blade is the largest and gradually decreases toward the root of the blade; the equivalent stress in the middle of the blade root is the largest and decreases as it moves toward the tip of the blade.

5 Conclusions

The hydrodynamic load on the propeller was calculated by using the CFD method, then the strength calculation on the blades of different materials was calculated, the stress and deformation distribution having been analyzed.

1) A numerical simulation is set up to analyze the open water performance of the DTMB 4119 standard propeller,and the simulation results are compared with test results from the literature to prove the reliability of the CFD calculation method.

2) Using ANSYS to perform a static analysis on the propeller, the stress distribution and blade deformation of the propellers made of different materials at different forward speeds can be obtained using the FSI technique.

3) In the future, more strength-sensitive propellers, such as highly skewed propellers,should be calculated.

Open Access This article is licensed under a Creative CommonsAttribution 4.0 International License, which permits use, sharing,adaptation,distribution and reproduction in any medium or format,as long as you give appropriate credit to the original author(s)and the source,provide a link to the Creative Commons licence,and indicate if changes were made.The images or other third party material in this article are included in the article's Creative Commons licence,unless indicated otherwise in a credit line to the material. If material is not included in the article's Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use,you will need to obtain permission directly from the copyright holder. To view a copy of this licence,visit http://creativecommons.org/licenses/by/4.0/.